Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
This post in the next paragraphs on the subject of How to Install a Bathtub is especially motivating. Try it and make your own personal results.
Mounting a bath tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a new one is likewise a reasonably hard job. If the old tub is easily accessible, the project can relocate immediately; if you have to open up a wall surface to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either instance, the project is within a residence handyman's skills, although you will need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the work and fit attempting it. Instead of employing a contractor to take over a halfway-completed task, it is better to consider using one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This article will aid you set up a brand-new bath tub in your restroom if you have actually already gotten a new tub and do not need to transform the arrangement of your previous supply of water pipelines.
Your tools and also product checklist need to make up the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bath needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the versatile faucet adapters to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, then the first thing you must do is detach the water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly bothersome because of the limited accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will certainly come from the pipelines. Once the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, put the tub in the called for position. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bathtub up until the spirit level reads degree.
To install taps, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water as well as inspect all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub and likewise check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been utilized at least once as this will settle it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washing machines are in location in between the faucet and also the sink. Protect the faucet in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The previous type ought to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split a stiff seal, triggering the water to permeate the wall between the bath as well as the tiling, bring about complications with dampness as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the motion experienced when the tub remains in usage. The sealant can break relatively early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that page on Installing A Bathtub while perusing the internet. If you enjoyed our blog entry please make sure you remember to pass it around. Thank you for going through it.
Visit Website Report this page